A CUTE BAG WITH 6″x6″ PAPER!

Yesterday I showed you some my projects for the 2017 Catalogue Sneak Peek Bloghop. It was 2 Double Z-fold cards and mini bags, (If you missed the HOP head back to my last post to see).   Today there is a little more time and I can show you how to make the cute little Berry Burst bags.  They are so easy and only use 1 square of 6″x6″ Designer Series Paper.  There are a few different versions of cute little bags on the blogosphere but I will show you how I made these ones. Here is the cute bag to show you again.  I have used the Color Theory Designer Series Paper Stack. 

MAKE YOUR OWN 6″x6″ BAG.

This bag would fit a couple of small chocolates or Lip Balm.

1. Take a piece of 15cm x 15cm (6″x6″) paper and you are going to score  your paper.  

Just a note first: If you are using the Color Theory DSP the colouring in the paper is an ombre effect ie going from dark to light.  You will want to think about how your paper will sit when you make it.  I have a turn-over edge on the bag at the top so you will want the colour running in a similar way for both sides.  So from dark to light.  Position your paper how you want it.  If the paper you are using is an all over pattern then you don’t need to worry too much how it runs.

Score your paper at 1.5cm (5/8″) and 6cm (2 1/4″).  Turn your paper 180′ and score the same on the other side at 1.5cm and 6cm (5/8″ and 2 1/4″)

Turn your paper 90′ to score the next sides.  Score at 3.2cm (1 1/4″).  Turn your paper 180′ and score 3.2cm again (1 1/4″).

Below is how it will look if you can see it OK.

2.  On the side score lines (widest score line) cut up on the 2 middle score lines up to the score line running down.  Fold on all of your score lines.

3. You will want to create your turn-over edge so turn your paper over to the other side.  Run your adhesive along the small tab on the top and bottom of your piece.  Then fold them over to adhere.

Place adhesive also on the centre tabs on the side which would be the pattern on the outside of your bag.

4. Fold up the centre tabs and adhere your side piece on to this.  Then place adhesive on the inside on the other tabs (as shown below) to fold up to form your box.  

<– Place adhesive on these lower tabs on the inside.

5. Once your box is assembled, push in on the ends to fold in.  Pinch on the folds to crease a little.

6. Add your handles as you like.  For this one I placed adhesive on each end of some ribbon and adhered to both ends of the bag.  To make the clasp, I punched out a strip of card with the Classic Label Punch and adhered this on to the bag with glue dots.  The flower is from the new ‘Seasonal Layers Thinlits’.  I added a Rhinestone to the centre. 

TIP: Colour your Rhinestones to match your project with a Sharpie.

Here is your finished bag.

Here are the 2 bags together.  Which is your favourite finish? I think I like the one with the snazzy clasp.

I hope you found this tutorial helpful and you could follow it OK?? I did make a video to show how to make this but between low flying planes and dogs barking and my bumbling along it wasn’t getting anywhere fast.  Let me know though if you would find a video helpful. 

Thanks for visiting,

Jenny

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s