3D projects, Tutorials

LOTS TO LOVE VALENTINE FLIP TOP BOX!

So it is Valentine’s Day here tomorrow apparently.  We don’t celebrate Valentine’s Day in a big way in Australia.  You might give your “significant other” a little chocolate treat and I do give my 2 kiddies (well they are mostly adults now), a little chocolate treat.

I thought that this year I should do SOMETHING! I have had the Lots to Love Box Framelits for a couple of weeks and not used them.  I had this in mind for about that long too.  So I just managed to create it in time.

I call it a Flip Top Treat Box. I am sure you could use the idea for a Gift Card not just chocolates.

This is with the Flip Top open. Mmm! Chocolate Hearts!

It has a little card insert in it to add the Chocolates. I added a Glue Dot under each one to stick them them to the card. I added a loop of ribbon which was adhered to the end of the card and then I added a small red punched circle to cover it.

CREATE YOUR OWN FLIP TOP TREAT BOX

1. Cut 2 of the box shapes from the Lots To Love Box Framelits from your card.

On one piece which will be your top score it at half way along the long side of the box. This will be at 6cm (2 3/8″) which is from the scored line measurement not from the start of the curved edge.

2. Place adhesive on the underside along the long tabs ONLY to the half way point that will be adhered to the box.  You don’t want to adhere the whole section or it won’t open. I added the adhesive on the curved end half.

3. Adhere the top piece to the bottom piece of the die-cut box.  Your bottom piece will have the curved end to the opening end as shown in the photo below.

4. Decorate the box as you like.  I used the Party Pandas set.  The hearts were cut from the Lots of Love Box Framelits set. The sentiment was cut with the Layering Square Framelits.

So cute enough for Valentine’s do you think?  Maybe it is a little late now to whip some up but file it away for another special Occasion.

Below I have a collage image ready to PIN.

Have a great day,

Jenny

 

 

 

 

 

 

 

3D projects, Classes, Tutorials

CLEAR BUNNY BOX FOR EASTER!

Easter is this weekend. Are you all sorted?? I had these little Lindt chocolate bunnies left over from class last week and wanted to make a special box for them.  I will show you what I created and I have the tutorial below to make your own.

It’s a little shallow box with a clear Acetate lid on top.  I realised one of the bunnies was a bit squashed but hey! I went with it still!! 🙂

TO MAKE YOUR OWN CLEAR BUNNY BOX

I have included Metric and Imperial but please check the Imperial measurements first. 🙂

Base:

15.4cm x 5.4cm. (6 1/8″ x 2 1/8).

Score at 1.2cm (1/2″) on all 4 sides.

Cut up on the small score lines on opposite ends.  Fold on all the scored lines. Add adhesive.  I used Fast Fuse.  Assemble your box.

Lid: 

*For Imperial measurements please test them first.

17cm x 14cm (6 3/4″ x 5 1/2″)

On the 17cm (6 3/4″) side score at 2cm and 15cm (1 3/16″and 5 7/8″)

On the 14cm side (5 1/2″) side score at  5.5cm and 8.5cm (2 3/16″ and 3 3/8″).

*Apologies for the photo quality.  It is a bit hard with the lighting and the shiny acetate.

Cut up on the small score lines on each side.  Fold on the score lines.  The acetate is hard to fold over but run along the folded line with your bone folder to press it down. Add your adhesive to the small tab at the side and down one of the side tabs.  Adhere together to form a box.

Hope that is clear?? Decorate as you like.

I wrapped around some Sweet Sugarplum Ruched ribbon, then decorated it with the diecut flower with the Stylish Stems Framelits.  The sentiment is from the Little Cuties set, cut with the Stitches Shapes Framelits and a small Layering Ovals Framelits.  I actually had these little “bits” on my desk from a project I didn’t end up using so that worked well.

I hope you like the cute box?? There is just enough time to make your own.

Jenny